Atempower AP110SG-FLEX User Manual

The Atempower AP110SG-FLEX is a versatile 110W portable solar generator designed for emergency backup, outdoor activities, and off-grid power. It features a high-capacity lithium-ion battery, multiple output ports (AC, DC, USB), MPPT solar charge controller, pure sine wave inverter, LCD display for system status, overload protection, and a durable, weather-resistant casing. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Solar Charging 8. Safety Features 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Lithium-ion Battery Pack, Pure Sine Wave Inverter, MPPT Charge Controller, LCD Display, AC Output Ports, DC Output Ports, USB Ports, Solar Input Port.

Feature	Description
AC Output	110V/60Hz pure sine wave for sensitive electronics
DC Output Ports	12V/10A for car appliances and DC devices
USB Ports	2x USB-A (5V/2.4A), 1x USB-C (PD 18W)
Solar Input	MPPT controller for efficient solar panel charging
LCD Display	Shows battery level, input/output power, warnings
Overload Protection	Automatic shutdown on overload or short circuit
Battery Management	Prevents overcharge, over-discharge, overheating
Car Charging	12V car adapter for charging from vehicle
Wall Charging	AC adapter for fast charging from wall outlet
Portable Handle	Integrated handle for easy transport

Installation

Unpack and inspect contents. Place on stable, dry surface.

Initial Charge: Connect to wall outlet using provided AC adapter for full charge.
Solar Panel Connection: Connect compatible solar panel to SOLAR INPUT port.
Device Connection: Plug devices into appropriate output ports (AC, DC, USB).
Power On: Press and hold POWER button for 3 seconds to activate unit.

WARNING! Do not expose to water or extreme temperatures. Ensure ventilation around unit during operation.

First-Time Setup

Power on unit; monitor LCD display.

Check Battery Level: Ensure battery is above 20% before first use.
Configure Output: Use MODE button to select output type (AC always on, DC auto-off).
Set LCD Brightness: Press and hold MODE + POWER to adjust display brightness.
Test Ports: Connect a small device to each port to verify functionality.

CAUTION! Use only provided or manufacturer-approved cables and adapters.

Specifications

Battery Capacity: 296Wh Lithium-ion.
AC Output: 110V, 60Hz, 110W (220W surge).
DC Output: 12V, 10A max.
USB Output: USB-A: 5V/2.4A; USB-C: PD 18W.
Solar Input: 12-24V, 10A max, MPPT.
AC Charging: 110V, 60Hz, 65W adapter.
Car Charging: 12V, 8A.
Display: LCD with backlight.
Operating Temp: 32°F to 104°F (0°C to 40°C).
Weight: 6.6 lbs (3 kg).

Controls and Settings

Front Panel: POWER Button, MODE Button, LCD Display, Output Ports.

LCD Icons: Battery Level, AC/DC/USB Output Status, Input Source, Warning Indicators.

Power Management: Press POWER to turn on/off; press MODE to cycle output modes (AC Always On, DC Auto-Off, ECO). Display Settings: Press MODE + POWER to adjust brightness. Reset: Hold POWER + MODE for 10 seconds to reset system settings.

Connecting Devices

AC Devices: Plug into AC outlet port. DC Devices: Use 12V car port adapter. USB Devices: Connect to USB-A or USB-C ports.

Check device power requirements (watts/amps).
Ensure total load does not exceed 110W for AC, 10A for DC.
Connect device cable to appropriate port.
Turn on device; monitor LCD for power draw.

Tip: Start with highest priority devices first to manage battery life.

Solar Charging

Supports 12V-24V solar panels up to 120W.

Connect solar panel to SOLAR INPUT port using provided cable.
Position panel in direct sunlight; angle for maximum exposure.
LCD will show solar icon and input wattage.
Charging stops automatically when battery is full.
For optimal charging, use panel with VOC between 18V-28V.

WARNING! Do not connect solar panel while devices are drawing high power. Avoid shading on panel.

Safety Features

Overload Protection: Automatic shutdown if load exceeds 110W. Short Circuit Protection: Cuts output on DC/USB short. Temperature Control: Reduces output if internal temp exceeds 140°F (60°C). Low Voltage Cutoff: Shuts down AC/DC outputs if battery drops below 10% to prevent damage.

Care & Maintenance

Store in cool, dry place. Clean with dry cloth; do not use liquids. Recharge every 3 months if storing long-term.

CAUTION! Do not disassemble battery pack. Avoid dropping or puncturing unit.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits. UL Certified: Meets safety standards for portable power stations. Copyright © 2025 Atempower; trademarks of Atempower Technologies. For support, visit www.atempower.com or contact 1-800-555-ATEM.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Unit won't power on	Battery depleted	Connect to AC or solar for charging; wait 5 minutes before retry.
No output from ports	Overload protection triggered	Disconnect all devices; press POWER to reset; reconnect one device at a time.
Solar not charging	Panel mismatch or shading	Ensure panel VOC is 18V-28V; check connections; reposition for full sun.
LCD shows warning icon	Overheating or low voltage	Move to cooler area; let unit cool; recharge battery.
Slow device charging	High simultaneous load	Disconnect non-essential devices; charge one high-power device at a time.

Reset: Hold POWER + MODE for 10 seconds to factory reset.

Service: 1-800-555-ATEM; www.atempower.com/support