Anker SOLIX PS400 User Manual

The Anker SOLIX PS400 is a 400W portable power station designed for outdoor adventures, home backup, and on-the-go power needs. It features a 512Wh LiFePO4 battery, multiple output ports (AC, USB-A, USB-C, DC), a 400W pure sine wave AC inverter, MPPT solar charging, and a user-friendly LCD screen. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Charging the Power Station 8. Safety Features 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: LiFePO4 battery pack, LCD display, AC output ports, USB ports, DC output ports, Solar charging input, AC charging input.

Feature	Description
AC Output	2 x 400W (800W surge) pure sine wave outlets
USB-A Output	2 x 12W USB-A ports for mobile devices
USB-C Output	1 x 60W USB-C PD port for fast charging
DC Output	1 x 12V/10A car port for car appliances
LCD Screen	Displays battery level, input/output wattage, and status
Solar Charging Input	Supports up to 200W solar panel input (11-28V)
AC Charging Input	Standard wall outlet charging (0-100% in ~6 hours)
Battery Type	LiFePO4 (Lithium Iron Phosphate), 512Wh capacity
Weight	Approx. 13.2 lbs (6 kg)
Operating Temp	14°F to 104°F (-10°C to 40°C)

Installation

Unpack and inspect contents. Place on stable, dry surface away from direct sunlight and moisture.

Initial Charge: Connect the included AC adapter to the AC input port and a wall outlet to fully charge before first use.
Solar Panel Connection: Use compatible solar panel with MC4 to XT60 cable (sold separately) for solar charging.
Device Connection: Connect your devices to the appropriate output ports (AC, USB, DC).
Power On: Press and hold the power button for 2 seconds to turn on the unit.

WARNING! Do not expose to water, fire, or extreme temperatures. Keep away from children.

First-Time Setup

Power on the unit; check LCD screen for battery status.

Fully charge: Use AC adapter to charge to 100% for optimal battery calibration.
Configure settings: Press the "i" button to cycle through display modes (input/output power, battery time remaining).
Test outputs: Connect a small device (e.g., phone) to USB port to verify operation.
Enable Eco Mode: Press and hold the "i" button for 5 seconds to turn on/off Eco Mode (auto-shutdown when load is low).

CAUTION! Use only Anker-approved accessories. Do not disassemble the unit.

Specifications

Capacity: 512Wh (46.08Ah @ 11.1V).
Battery Chemistry: LiFePO4 (3000+ life cycles to 80% capacity).
AC Inverter: 400W rated, 800W surge, pure sine wave.
Inputs: AC (120V, 60Hz, 90W max), Solar (11-28V, 200W max).
Outputs: AC x2, USB-A x2 (12W), USB-C x1 (60W PD), DC x1 (12V/10A).
Display: LCD showing battery %, input/output power, remaining time.
Weight: 13.2 lbs (6 kg).
Dimensions: 10.6 x 7.1 x 7.5 in (27 x 18 x 19 cm).
Certifications: FCC, CE, RoHS, PSE.

Controls and Settings

Access controls via physical buttons and LCD screen. Front Panel: Power button, "i" button, AC output button, DC output button, USB output button.

LCD Display: Shows battery percentage, input/output power in watts, estimated time remaining, and warning icons.

Settings: Eco Mode (auto-shutdown), Screen brightness (press "i" to adjust), Buzzer on/off (hold AC and DC buttons for 3 seconds). Charging: Select AC or solar input; unit auto-detects source. Output: Press respective output button to turn ports on/off. Battery protection: Built-in BMS for over-voltage, over-current, short-circuit, and temperature protection.

Connecting Devices

AC Devices: Plug into AC outlets (max 400W total). USB Devices: Use USB-A for phones/tablets, USB-C for laptops. DC Devices: Use 12V car port for car fridge, air pump, etc.

Check device power requirements (watts/volts) before connecting.
Turn on the power station first, then turn on the output button for the port you're using.
Connect device cable to the appropriate port.
Monitor LCD screen for output power and battery level.

Tip: Do not exceed 400W total output. High-wattage devices (e.g., electric kettle) may trigger overload protection.

Charging the Power Station

Supports AC wall charging and solar charging.

AC Charging: Plug AC adapter into AC input port and wall outlet. Charging time: ~6 hours.
Solar Charging: Connect solar panel to solar input port using MC4 to XT60 cable. Ensure panel is in direct sunlight. Max 200W input.
Dual Charging: Not supported; unit will prioritize AC if both are connected.
Monitoring: LCD shows input power, battery percentage, and estimated time to full.
Battery Care: For storage, charge to 80% and store in cool, dry place. Recharge every 3 months.

WARNING! Use only approved solar panels. Do not charge in temperatures below 14°F (-10°C) or above 104°F (40°C).

Safety Features

Battery Management System (BMS): Protects against overcharge, over-discharge, over-current, short circuit, and high temperature. Temperature Control: Auto-shutdown if internal temperature exceeds 149°F (65°C). Fire Resistance: LiFePO4 battery is more stable and less prone to thermal runaway than other lithium batteries.

Care & Cleaning

Turn off and unplug all devices before cleaning. Use dry, soft cloth to wipe exterior. Do not use liquids or abrasive cleaners.

CAUTION! Do not immerse in water. Avoid exposure to rain or moisture. Store in dry environment.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © 2023 Anker Innovations Limited; trademarks of Anker. For support, visit www.anker.com or contact 1-800-988-7973.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Unit won't turn on	Battery depleted	Charge using AC adapter for at least 30 minutes before use.
No output from ports	Output not enabled/overload	Press corresponding output button; check if overload icon appears (reduce connected load).
Solar not charging	Insufficient sunlight/connection	Ensure solar panel is in direct sun; check cable connections; verify panel voltage (11-28V).
LCD screen blank	Sleep mode/battery save	Press any button to wake; if still blank, charge unit.
Over-temperature warning	High ambient temperature	Move unit to cooler location; allow to cool before use.

Reset: Turn off all outputs, disconnect all devices, and restart unit.

Service: 1-800-988-7973; www.anker.com