Anker SOLIX PS100 User Manual

The Anker SOLIX PS100 is a portable power station designed for reliable backup power and outdoor use. It features a 1000Wh capacity, multiple output ports (AC, USB-A, USB-C, DC), pure sine wave AC output, fast recharging via solar or wall outlet, an LCD screen for monitoring, and advanced battery management for safety. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Charging & Discharging 8. Safety Features 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Lithium-ion battery pack, LCD display, AC outlets, USB ports, DC outputs, solar charging input, power button, and cooling fan.

Feature	Description
AC Output	Pure sine wave, 1000W continuous (2000W surge)
USB-C Port	100W PD for fast charging laptops and devices
USB-A Ports	Multiple ports for phones, tablets, and accessories
DC Output	12V carport and 5521 barrel jack for DC devices
Solar Charging Input	Supports up to 200W solar panel input
LCD Display	Shows battery level, input/output wattage, and status
Power Button	Turns unit on/off and controls output ports
Cooling Fan	Automatically activates during high load or charging
Battery Management System	Protects against overcharge, over-discharge, and short circuits
Carrying Handle	Integrated for easy portability

Installation

Unpack and inspect contents. Place on stable, dry surface away from direct sunlight and heat sources.

Initial Charge: Connect the included AC adapter to the unit and a wall outlet. Allow to charge fully (approx. 7 hours).
Solar Panel Setup: Connect compatible solar panel to the DC input port using the provided cable.
Device Connection: Plug devices into appropriate output ports (AC, USB, DC).
Power On: Press and hold the power button for 3 seconds to turn on the unit.

WARNING! Do not expose to water or extreme temperatures. Ensure ventilation around the cooling fan.

First-Time Setup

Power on the unit; monitor LCD screen for status.

Check Battery Level: Ensure battery is above 20% before first use.
Configure Output Settings: Use the mode button to switch between AC always-on, eco mode, or scheduled operation.
Set Display Brightness: Press and hold the mode button to adjust LCD brightness.
Update Firmware (if applicable): Connect to the Anker app via Bluetooth for updates.

CAUTION! Use only Anker-approved cables and adapters. Do not disassemble the unit.

Specifications

Capacity: 1000Wh (Lithium-ion).
AC Output: 120V, 60Hz, pure sine wave, 1000W continuous, 2000W surge.
USB-C Output: 100W Power Delivery.
USB-A Output: 5V/2.4A per port.
DC Output: 12V/10A (carport), 12V/5A (5521 jack).
Solar Input: 11-28V, up to 200W.
AC Charging Input: 100-240V, 50/60Hz, 150W max.
Weight: Approx. 22 lbs (10 kg).
Operating Temperature: 32°F to 104°F (0°C to 40°C).
Storage Temperature: -4°F to 113°F (-20°C to 45°C).

Controls and Settings

Access settings via the mode button and LCD screen. Front Panel: Power button, mode button, LCD display, output ports.

Remote Monitoring (via App): Connect to the Anker app for detailed stats, remote control, and firmware updates.

Output Control: Toggle AC, USB, and DC outputs individually via the mode button. Display: Shows battery percentage, input/output power, estimated runtime, and warnings. Settings: Eco mode (auto-shutoff when no load), screen timeout, unit beep on/off.

Connecting Devices

AC Devices: Plug into AC outlets (max 1000W total). USB Devices: Connect to USB-A or USB-C ports. DC Devices: Use carport or 5521 jack.

Turn off the power station before connecting high-wattage devices.
Match device power requirements to output specifications.
Turn on the power station, then enable the specific output port if needed.

Tip: For sensitive electronics (e.g., medical devices, audio equipment), use pure sine wave AC output.

Charging & Discharging

Supports AC wall charging, solar charging, and 12V car charging.

AC Charging: Use included adapter; full charge in ~7 hours.
Solar Charging: Connect compatible panel; ensure direct sunlight for optimal performance.
Discharging: Monitor battery level on LCD; unit will beep at low battery (10%).
Simultaneous Charge/Discharge: Supports pass-through charging (charge while powering devices).
Battery Saving Mode: Enable eco mode to auto-shutoff AC output when no load detected.

WARNING! Do not exceed max input/output ratings. Disconnect solar panels during storms.

Safety Features

Overcharge/Over-discharge Protection: Automatically stops charging/discharging at safe limits. Short Circuit Protection: Shuts off output if short detected. Over-temperature Protection: Reduces power or shuts down if overheated. Low-temperature Charging Protection: Prevents charging below 32°F (0°C).

Care & Maintenance

Store in cool, dry place. Clean with dry cloth; do not use liquids. Periodically charge to 50-80% if storing long-term.

CAUTION! Do not attempt to open or repair the unit. Contact Anker support for service.

Regulatory Information

Troubleshooting

Symptom	Possible Cause	Corrective Action
Unit not powering on	Battery depleted	Connect to AC or solar charger; allow to charge for 30 minutes before turning on.
No output from AC ports	Eco mode enabled/overload	Disable eco mode; ensure total load is under 1000W; check for overload shutdown.
Slow solar charging	Insufficient sunlight/panel mismatch	Ensure panel is in direct sunlight; verify panel voltage is within 11-28V range.
LCD display blank	Screen timeout/unit off	Press any button to wake display; ensure unit is powered on.
Overheating warning	High ambient temperature/blocked fan	Move to cooler location; ensure ventilation around fan is clear.

Reset: Hold power and mode buttons for 10 seconds to reset system settings.

Service: 1-800-988-7973; www.anker.com