Allpowers B01MU0WMGT Manual

The Allpowers B01MU0WMGT is a portable power station designed for outdoor activities, emergency backup, and off-grid power needs. It features multiple output ports including AC, DC, USB-A, and USB-C, supports solar charging, has a high-capacity lithium battery, LCD display for status monitoring, overload protection, and pure sine wave AC output. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Charging the Power Station 8. Safety Features 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: High-capacity lithium battery, LCD display, AC outlets, DC carport, USB ports, solar charging input, cooling fan, power button, LED indicators.

Feature	Description
AC Output	Pure sine wave AC outlets for sensitive electronics
DC Output	12V carport for DC devices
USB-A Ports	Standard USB ports for charging phones and tablets
USB-C Port	Fast charging USB-C port with PD support
Solar Charging Input	For connecting solar panels for renewable charging
LCD Display	Shows battery level, input/output power, and status
Power Button	Turns the power station on/off
Overload Protection	Automatically shuts off if overload is detected
Cooling Fan	Activates during high load to prevent overheating
LED Indicators	Show charging status and output activity

Installation

Unpack and inspect contents. Place on stable, dry surface.

Initial Charge: Connect the included AC adapter to charge the unit fully before first use.
Connect Solar Panels: Use compatible solar panels with MC4 connectors to the solar input port.
Positioning: Ensure adequate ventilation around the unit, especially the cooling fan vents.
Storage: Store in a cool, dry place away from direct sunlight and moisture.

WARNING! Do not expose to water or extreme temperatures. Keep away from flammable materials.

First-Time Setup

Power on the unit; monitor LCD display for status.

Initial Charge: Plug into AC outlet using provided adapter until battery is 100%.
Power On: Press and hold the power button for 3 seconds to turn on.
Check Outputs: Verify all output ports are functioning by connecting a small device.
Configure Settings: Use the LCD display to set auto-shutdown timer if needed.

CAUTION! Do not connect devices exceeding the maximum output rating. Ensure proper ventilation during use.

Specifications

Battery Capacity: High-capacity lithium (specific watt-hour rating).
AC Output: Pure sine wave, 120V, 60Hz.
DC Output: 12V carport.
USB Outputs: USB-A and USB-C with Power Delivery.
Solar Input: Compatible with solar panels up to specified wattage.
Charging Methods: AC wall outlet, solar panel, car charger.
Display: LCD showing battery level, input/output power, and warnings.
Weight: Portable design for easy transport.
Operating Temp: 32°F to 104°F (0°C to 40°C).

Controls and Settings

Access settings via the LCD display interface. Front Panel: Power button, LCD display, output ports.

LCD Display: Shows battery percentage, input power (W), output power (W), estimated runtime, and error codes.

Settings Menu: Auto-shutdown timer (2/4/6/8 hours), LCD brightness, beep on/off, battery calibration. Protection Features: Overload, over-temperature, short-circuit, low-voltage, over-voltage protection.

Connecting Devices

AC Devices: Plug into AC outlets. DC Devices: Use 12V carport. USB Devices: Connect to USB-A or USB-C ports.

Ensure the power station is turned on.
Connect devices to appropriate ports.
Monitor LCD display for power draw and battery level.
Disconnect devices when not in use to conserve battery.

Tip: Start with the device powered off, then turn it on after connecting to avoid sparking.

Charging the Power Station

Supports AC wall charging, solar charging, and car charging.

AC Charging: Use included AC adapter; plug into wall outlet and the unit's AC input port.
Solar Charging: Connect compatible solar panels to solar input; ensure proper alignment to sunlight.
Car Charging: Use 12V car charger adapter while vehicle is running.
Charging Status: LCD display shows charging progress and estimated time to full.
Fast Charging: Some models support fast charging via AC or solar when conditions allow.

WARNING! Use only recommended chargers and solar panels. Do not charge in extreme temperatures.

Safety Features

Overload Protection: Automatically cuts power if connected devices exceed rated output. Temperature Control: Fan activates during high load; unit shuts down if overheated. Short-Circuit Protection: Prevents damage from faulty cables or devices.

Care & Maintenance

Keep unit clean and dry. Wipe with a dry cloth; do not use liquids. Store with 50-80% charge if not used for extended periods.

CAUTION! Do not disassemble; no user-serviceable parts inside. Avoid dropping or physical impact.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits. CE, RoHS compliant. Copyright © Allpowers; trademarks of Allpowers Technology Co., Ltd. For support, visit www.allpowers.com or contact customer service.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Unit won't turn on	Battery depleted	Charge the unit fully; press and hold power button.
No output from ports	Overload protection triggered	Disconnect all devices, wait 30 seconds, then reconnect one at a time.
Slow charging	Low input power source	Use higher wattage charger or ensure solar panels are in direct sunlight.
LCD display blank	Unit in sleep mode	Press any button to wake display; check battery level.
Overheating	High ambient temperature or blocked vents	Move to cooler location; ensure ventilation around fan vents.

Reset: Turn off, disconnect all devices, wait 1 minute, then turn on.

Service: Contact customer support; do not attempt to repair yourself.