Aims Power PV130CASE Instructions

The Aims Power PV130CASE is a portable power station designed for reliable off-grid and emergency power. Featuring a high-capacity lithium battery, multiple AC and DC outputs, USB charging ports, and pure sine wave inverter technology, it provides clean, stable power for sensitive electronics, tools, and appliances. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Safety Information 3. Initial Setup & Charging 4. Specifications 5. Controls and Ports 6. Operating Instructions 7. Charging Methods 8. Maintenance & Storage 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: High-capacity Lithium Battery, Pure Sine Wave Inverter, LCD Display, Multiple AC Outlets, DC Outputs, USB Ports, and Solar Charge Input.

Feature	Description
AC Output	Pure sine wave AC outlets for sensitive electronics
DC Output	12V carport and regulated DC outputs
USB Ports	USB-A and USB-C for charging mobile devices
LCD Display	Shows battery level, input/output wattage, and status
Solar Charge Input	MPPT controller for efficient solar panel charging
AC Charging	Fast wall charging via included adapter
Car Charging	12V vehicle charging capability
Overload Protection	Automatic shutdown on overload or short circuit
Battery Management System	Protects against overcharge, over-discharge, and overheating
Portable Design	Integrated handle for easy transport

Safety Information

Read all instructions before use. Keep unit away from water, heat sources, and flammable materials.

Do not disassemble, modify, or puncture the battery or casing.
Use only with recommended charging sources and cables.
Ensure proper ventilation during operation and charging.
Disconnect loads before turning the unit off.
Keep out of reach of children and pets.

WARNING! Risk of fire or electric shock if misused. Do not expose to rain or moisture. Use only in dry conditions.

Initial Setup & Charging

Before first use, fully charge the unit.

Unpack and inspect for damage.
Connect the included AC adapter to the unit and a wall outlet.
The LCD will display charging status. Charge until battery indicator shows 100%.
For solar charging, connect compatible solar panel to the DC input port.
Fully charge before extended storage.

CAUTION! Use only the provided or Aims Power-approved charging accessories. Incorrect chargers can damage the battery.

Specifications

Battery Capacity: 1300Wh Lithium (LiFePO4).
AC Output: 120V, 60Hz, Pure Sine Wave, 1000W continuous (2000W surge).
DC Output: 12V/10A (car port), 12V/3A (regulated).
USB Output: USB-A (5V/2.4A), USB-C (PD 60W).
Solar Input: 12-48V DC, 500W max with MPPT.
AC Charging Input: 120V AC, 60Hz.
Car Charging Input: 12V DC.
Display: LCD with battery level, input/output power, fault indicators.
Operating Temp: 32°F to 104°F (0°C to 40°C).
Weight: Approximately 30 lbs.

Controls and Ports

Front Panel: LCD Display, AC Output Switch, DC Output Switch, USB Ports.

Side/Rear Ports: AC Charging Input, Solar/DC Charging Input, 12V Car Output, 12V Regulated Output, Ground Terminal.

LCD Display Icons: Battery Percentage, Input/Output Wattage, Warning Indicators (Overload, Over-temperature, Short Circuit). Controls: Master Power Button, AC Output Button, DC Output Button, LCD Backlight Button.

Operating Instructions

Powering Devices: Connect device to appropriate output port and turn on the corresponding output switch.

Turn on the unit with the Master Power Button.
For AC devices: Plug into AC outlet, press AC Output Button.
For DC devices: Plug into 12V carport or regulated port, press DC Output Button.
For USB devices: Plug directly into USB-A or USB-C port (always active when unit is on).
Monitor battery level on LCD display.
Turn off outputs and master power when not in use to conserve battery.

Tip: Start with the highest power draw device first to avoid overloading the system.

Charging Methods

Supports three charging methods: AC Wall Outlet, Solar Panel, and 12V Car Outlet.

AC Charging: Connect included AC adapter. Fastest method.
Solar Charging: Connect compatible solar panel to DC input. Ensure proper polarity and voltage (12-48V DC).
Car Charging: Connect 12V car charger cable to DC input and vehicle's 12V outlet.
Charging status is shown on LCD. Do not exceed max input ratings.
Unit can be used while charging (pass-through charging).

WARNING! Use only solar panels with voltage within specified range. Incorrect voltage can damage the charge controller.

Maintenance & Storage

Clean with dry cloth only. Store in a cool, dry place.

For long-term storage, charge battery to 50-80%.
Recharge every 3-6 months to maintain battery health.
Do not store in temperatures below -4°F (-20°C) or above 140°F (60°C).
Keep terminals clean and free of corrosion.

CAUTION! Do not immerse in water or use abrasive cleaners. Avoid storing in fully discharged state.

Regulatory Information

FCC Part 15: Class B digital device; complies with limits for residential use. UL Standards: Designed to meet safety standards. Copyright © Aims Power. For support, visit www.aimscorp.com or contact 1-800-605-6427.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Unit will not turn on	Battery depleted	Connect to AC or solar charger to recharge.
No output power	Outputs turned off/overload	Press corresponding output button; check for overload and disconnect some devices.
LCD shows fault code	Overload/short circuit/high temp	Turn unit off, disconnect all loads, allow to cool, then restart.
Not charging from solar	Insufficient sun/incorrect connection	Check solar panel alignment and cable connections; verify panel voltage.
Reduced runtime	Battery aging/high load	Reduce connected load; consider battery replacement if significantly degraded.
Fan runs continuously	High ambient temperature/heavy load	Ensure proper ventilation; reduce load if possible.

Reset: Turn unit completely off and on again. For persistent faults, contact support.

Service: 1-800-605-6427; www.aimscorp.com