Acopower PE-LTK-3x40W Product Introduction

The Acopower PE-LTK-3x40W is a high-performance LED tube light kit designed for energy-efficient illumination in commercial and industrial settings. This kit includes three 40W LED tubes with a high lumen output, compatible ballast bypass or direct wire installation, a color temperature of 5000K (daylight), high CRI for accurate color rendering, and a long lifespan of up to 50,000 hours. It is suitable for retrofitting existing fluorescent fixtures or new installations. Below are key sections for features, installation, specifications, operation, and safety information.

1. Features at a Glance 2. Installation Guide 3. First-Time Setup 4. Specifications 5. Controls and Operation 6. Wiring Configuration 7. Maintenance & Care 8. Safety Information 9. Regulatory Compliance 10. Troubleshooting

Features at a Glance

Key components: Three 40W LED tubes, wiring connectors, mounting brackets, and installation manual.

Feature	Description
High Lumen Output	Delivers up to 4500 lumens per tube for bright, even illumination
Energy Efficient	Consumes up to 50% less energy compared to traditional fluorescent tubes
Long Lifespan	Rated for up to 50,000 hours of operation
Color Temperature	5000K daylight white for clear, natural lighting
High CRI	80+ Color Rendering Index for accurate color representation
Installation Flexibility	Compatible with ballast bypass or direct wire setups
Durable Construction	Made with polycarbonate diffuser and aluminum heat sink
Wide Voltage Range	Operates on 100-277V AC, 50/60Hz
Instant On	No warm-up time; full brightness immediately
Dimmable Option	Compatible with compatible dimmers (if specified)

Installation Guide

Unpack and inspect all components. Ensure power is turned off at the circuit breaker before installation.

Remove existing fluorescent tubes and ballast (for ballast bypass installation).
Install mounting brackets securely to the fixture or ceiling.
Connect LED tubes using provided wiring connectors following wiring diagram.
Secure tubes into brackets and ensure all connections are tight.
Restore power and test operation.

WARNING! Installation should be performed by a qualified electrician. Ensure all power is disconnected before beginning work to avoid electrical shock.

First-Time Setup

After installation, verify proper operation and adjust as needed.

Power on the circuit and check all three tubes illuminate.
Verify even light distribution and absence of flickering.
If dimmable, test dimmer functionality with compatible dimmer switch.
Adjust mounting angle if necessary for optimal light coverage.

CAUTION! Do not touch LED tubes with bare hands during installation; use gloves to prevent oil residue affecting performance.

Specifications

Model: PE-LTK-3x40W
Power per Tube: 40W
Luminous Flux: 4500 lumens per tube
Color Temperature: 5000K (Daylight)
CRI: 80+
Input Voltage: 100-277V AC, 50/60Hz
Power Factor: >0.9
Beam Angle: 120 degrees
Lifespan: Up to 50,000 hours
Operating Temperature: -20°C to 40°C (-4°F to 104°F)
Dimensions per Tube: 48 inches (1219mm) length, 1 inch (25mm) diameter
Certifications: UL Listed, Energy Star compliant (if applicable)

Controls and Operation

Operation is via standard wall switch or compatible dimmer. No dedicated remote control included.

Basic Operation: Turn power on/off using wall switch. For dimmable models, adjust light level using compatible dimmer switch.

Maintenance Mode: No user-serviceable parts inside. For cleaning, power off and follow care instructions.

Wiring Configuration

Two installation methods: Ballast Bypass (recommended) or Direct Wire with existing ballast (if compatible).

Ballast Bypass: Remove existing ballast, wire AC power directly to LED tube sockets.
Direct Wire (if compatible): Use with specified electronic ballasts; follow manufacturer wiring diagram.

Tip: Always refer to the included wiring diagram specific to your fixture type. Use wire nuts and electrical tape for secure connections.

Maintenance & Care

Regular maintenance ensures optimal performance and longevity.

Turn off power and allow tubes to cool before cleaning.
Clean tubes and fixture with a soft, dry cloth. For stubborn dirt, use a damp cloth with mild detergent, then dry thoroughly.
Inspect wiring connections annually for looseness or corrosion.
Replace tubes if noticeable dimming or flickering occurs after prolonged use.

CAUTION! Do not use abrasive cleaners or solvents. Never spray liquids directly onto tubes or electrical components.

Safety Information

Read all instructions before installation and operation.

Disconnect power at the circuit breaker before installation or maintenance.
Installation must comply with all local and national electrical codes.
Do not install in wet or damp locations unless rated for such environments.
Ensure adequate ventilation around fixtures to prevent overheating.
Keep away from flammable materials.

Regulatory Compliance

This product complies with relevant safety and performance standards.

UL Listed: Meets Underwriters Laboratories safety standards.
FCC Part 15: Class B digital device; complies with interference limits.
Energy Star: May qualify for Energy Star certification (check specific model).
RoHS: Compliant with Restriction of Hazardous Substances directive.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Tube does not light	Power off / Loose connection	Check circuit breaker; ensure power is on. Verify all wiring connections are secure.
Flickering light	Incompatible ballast / Poor connection	For ballast bypass, ensure ballast is removed. Tighten all wire connections.
Dim output	End of life / Voltage issue	Tubes may need replacement after 50,000 hours. Check input voltage is within 100-277V AC.
Buzzing sound	Ballast issue / Loose parts	In ballast bypass, ensure ballast is disconnected. Tighten mounting hardware.
Partial lighting	Defective tube / Wiring error	Swap tubes to identify faulty one; replace if necessary. Review wiring diagram.

Reset: Turn power off for 30 seconds, then restore power.

Service: For technical support, contact 1-800-555-ACOP or visit www.acopower.com/support.